Seven tightly integrated services sharing a single coordinated model, backed by automated checks and engineer review. Each section below is interactive — run the clash cycle, drag the parameters, scrub the sequence.
SERVICE / 01
BIM Modelling
High-detail models authored to your project standards and LOD matrix — with deep MEP specialisation backed by architectural and structural capability.
Mechanical & plumbing
HVAC, piping & plumbing systems
Mechanical equipment & plant room layouts
Fire protection & sprinkler systems
Electrical & low voltage
Power, lighting & distribution
Cable tray, duct bank, conduit & sleeving
Electrical & communications room coordination
Fire alarm, security, communications & AV
Architecture & structure
Architectural models from concept to as-built
Concrete, steel & framing models with embeds
RevitAutoCADDynamoIFCLOD 100–500
Corridor section · Toggle disciplines
Visible disciplines 3 / 3Elements in view 85
SERVICE / 02
Coordination & Clash Detection
We run multi-trade coordination so conflicts are found and closed before they reach the field — resolved on screen, at a fraction of what they cost in a ceiling.
What we deliver
Combined federated coordination models
Rule-based clash tests with agreed tolerances
Issue reporting & tracking to closure (BCF)
Coordination meetings chaired on your cadence
Sign-off ready coordinated models per zone
Where it pays back
Fewer field changes and less rework
Faster, more predictable installation
Trades that agree before they mobilise
NavisworksAutodesk Construction CloudReviztoBCF
Ready to test
CLASH-0042 · SA duct × beam B-12OPEN
CLASH-0043 · CHW pipes × beam B-14OPEN
CLASH-0044 · Cable tray × beam soffitOPEN
SERVICE / 03
Shop Drawings & As-Builts
Installation drawings generated from the coordinated model — dimensioned to gridlines and levels your crews already work to, then updated to as-built once installed.
Deliverables
Duct & sheet metal installation drawings
Piping & plumbing shop drawings with spools
Conduit, cable tray & containment layouts
Coordinated sleeve & penetration drawings
Hanger & support coordination drawings
As-built models and record drawings
RevitAutoCADPDF / DWGYour title block
M-401 · Extracted from the model
Sheet content is generated from model geometry — no redrawing, no drift from the coordinated model.
SERVICE / 04
Revit Family Creation
Custom parametric families built to your graphics and data standards — clean, lightweight, and driven by the parameters your team actually schedules on.
What we build
Mechanical & electrical equipment
Plumbing fixtures & specialties
Architectural & joinery components
Manufacturer content rebuilt to be model-safe
Shared parameters, type catalogues & MEP connectors
Family EditorShared parametersType cataloguesNested arraysClearance solids
Panelboard family · ParametricDB-24W-600
24
600 mm
Enclosure height 950 mmCircuits 24
SERVICE / 05
Scan-to-BIM
Registered point clouds turned into dimensionally reliable as-built models — the foundation for renovation, retrofit, tie-ins, and facility data.
Deliverables
Point cloud registration & clean-up
Architectural, structural & MEP as-built models
Modelling to an agreed tolerance band
Deviation reporting against the cloud
ReCap ProRevitE57 / RCPLOD 300–500
MODELLING · IN PROGRESS
Model
Conversion 35%Modelled to an agreed tolerance, verified against the registered cloud.
SERVICE / 06
4D Sequencing & Simulation
The model linked to the programme, so sequence, logistics, and phasing can be reviewed and agreed before the first crew mobilises. Scrub the timeline to build the structure.
Includes
Model linked to programme activities
Construction sequence animations
Site logistics & crane/access studies
Phasing visuals for stakeholder review
Navisworks TimeLinerPrimavera P6MS ProjectSynchro data
Zone B tower · SequenceWEEK 00 / 24
Current activity SuperstructureLevels complete 4 / 8
SERVICE / 07
5D Quantification
Model-based quantities for estimating and procurement — takeoffs that regenerate when the design moves, with a clear audit trail back to the elements they came from.
Capabilities
Model-based quantity takeoff by system & zone
Revision-to-revision quantity comparison
Structured exports into your estimating system
Procurement & material release schedules
Model-based QTOExcel / CSVYour BoQ structure
Sample takeoff · Select a row
Illustrative model-based quantity takeoff. Select a row to highlight the matching elements in the section above.
Element
Unit
Qty
Ductwork
m²
0
Pipework
m
0
Cable tray
m
0
Conduit
m
0
Slab sleeves
nr
0
Slab penetration area
m²
0
SAMPLE TAKEOFF — ILLUSTRATIVE QUANTITIES, NOT PROJECT DATA
SERVICE / 08
Automation & Model Assurance
Scripted checks that run on every model drop, so quality control does not depend on memory or spare time. Findings are prioritised by software and reviewed by an engineer before they reach you.
Clash triage — grouping and ranking issues before review
Asset data completeness checks for handover
Where the line sits
Automation narrows where a person looks. It does not approve a model, sign a drawing, or change design intent. Every finding is assessed by a qualified BIM engineer, and anything affecting design is raised with your team rather than resolved unilaterally.
Illustrative rule set. On a live project the rules come from your BEP and standards.
Frequently asked questions
What contractors usually ask first.
How do we start, and what do you need from us?
Send whatever exists — drawings, a model, a specification, or just a scope description. We come back within one business day with an approach, a programme, and a fee. Before modelling starts we agree the BEP, LOD matrix, naming conventions, templates, and where files live.
Do you work inside our CDE and standards, or your own?
Yours. We author inside your common data environment, to your naming and classification conventions, using your templates and title blocks. The deliverable should look like it came from your own team, because handover is far cheaper when nothing needs translating.
How do you engage — project, retainer, or overflow support?
All three. Project-based for a defined scope with fixed milestones; a dedicated team embedded across your projects month to month; or on-demand capacity when a deadline spikes and you need families, drawing sets, or a clash cycle turned around without adding headcount.
What LOD do we actually need?
It depends on what the model has to answer. LOD 300 supports coordination and permit documentation; LOD 350 adds the interfaces and supports trades need to install; LOD 400 carries fabrication detail; LOD 500 is the field-verified record. Most contractor coordination work sits at 350, and we will tell you if you are being asked to pay for detail the project will not use.
How is our project information kept confidential?
We work under your NDA and your access controls, inside your CDE wherever possible, with named team members and access removed at project close. If you have specific data-handling requirements, raise them at the scoping stage and we will confirm in writing what we can meet.
Do you work across time zones?
Yes. We schedule coordination sessions and model drops around your working hours and milestone dates wherever your team is based, and agree the meeting cadence and review windows as part of the delivery plan.
Scope in hand?
Get an approach and a quote within one business day.
Share your drawings, models, or point clouds — we'll review them and come back with a clear plan.
